Welcome to ecuobd2.com!
Search Site

Cart 0 item

Ford 3 button Remote control

SKU: TRK-FORD-R02-315

Availability: In stock

Regular Price: $12.00

Special Price: $11.00 9% Off


Weight: 0.10 kg (Add to Cart to Estimate Shipping Cost)
Ford 3button Remote control

You may also be interested in the following product(s)

ID 4D- 60 chip (Glass) for Ford

ID 4D- 60 chip (Glass) for Ford

$6.60
Ford Mondeo Remote Key 433MHz 4C Glass Chip Inside

Ford Mondeo Remote Key 433MHz 4C Glass Chip Inside

$24.00
FORD 2+1 Remote control 433MHz

FORD 2+1 Remote control 433MHz

$26.00
Ford new 80bit transponder chip

Ford new 80bit transponder chip

$9.00

Details

Programming procedure for:(below)
**1999-2012 Lincoln LS - Dealer program only**
2000-2012 Escape              2004-2006 Freestar                    2003-2008 Lincoln Aviator               1999-2003 Windstar
1999-2003 Escort                2006-2012 Fusion                       1999-2012 Mustang                          2005-2012 Mercury Mariner
1998-2001 Explorer             2004-2012 Lincoln Town Car    1998-2012 Ranger                            1998-2012 Mazda B Series
2000-2012 Excursion          2001-2012 Mazda Tribute          1998-2012 Mercury Mountaineer     1998-2012 Ford Econoline
1998-2012 Expedition         1999-2012 Mercury Sable          1998-2012 Taurus                              2007-2013 Ford Edge
2005-2011 Five Hundred    1999-2003 Mercury Tracer          2002-2006 Thunderbard                   2005-2012 Mercury Montego

1.Keep your foot off the brake pedal. (Ford Econoline only set parking brake)
2.Insert the key in the ignition and turn it from OFF to RUN 8 times within 10 seconds. On the 8th turn leave the ignition on RUN. When done correctly the door locks will cycle to signal entry into programming mode(off is where you can remove the key and run is the position just before the engine will start) If the door locks don't cycle the process is not being done correctly or the vehicle is not equipped with keyless entry.
3.Within 20 seconds press the lock button on all keyless remotes being programmed including any existing remotes. The doors locks will cycle to confirm successful programming of each remote.
4.Turn the ignition to the OFF position to end programming mode. Test all remotes to confirm successful programming.


------------------------------------------------------------------------------------------------------------------------


1998-2012 Ford F150 F250 F350 F450        2005-2007 Ford Freestyle           1998-2008 Lincoln Navigator
2000-2012 Ford Sport Trac                              2002-2012 Ford Explorer
1.Keep your foot off the brake pedal, close all doors, open drivers door and press the unlock button on the door itself.(not the remote)
2.Insert the key in the ignition and turn it from OFF to RUN 8 times within 10 seconds. On the 8th turn leave the ignition on RUN. When done correctly the door locks will cycle to signal entry into programming mode(off is where you can remove the key and run is the position just before the engine will start) If the door locks don't cycle the process is not being done correctly or the vehicle is not equipped with keyless entry.
3.Within 20 seconds press the lock button on all keyless remotes being programmed including any existing remotes. The doors locks will cycle to confirm successful programming of each remote.
4.Turn the ignition to OFF position to end programming mode. Test all remotes to confirm successful programming.
If vehicle does not go into programming mode turn ignition from OFF to RUN 5 times instead of 8 or shut the door after opening it in step 1.


------------------------------------------------------------------------------------------------------------------------


2000-2012 Ford Focus (2008+ turn 8 times not 4 in step 2)
1.Keep your foot off the brake pedal, close all doors and fasten seat belts.
2.Insert the key in the ignition and turn it from OFF to RUN 4 times within 6 seconds. On the 4th turn leave the ignition on RUN, wait 1 second. (off is where you can remove the key and run is the position just before the engine will start)
3.Turn the ignition to OFF. A light will illuminate and an acoustic sound will be heard to confirm programming mode.(light is usually in the top right of the inst cluster)
4.Within 10 seconds press and hold the lock button on the first remote being programmed. A light will flash and an acoustic sound will be made by the car to confirm successful programming. Wait 2 seconds and repeat this process for all additional remotes being programmed or continue to step 4 if programming a single remote.
5.Turn the ignition to CRANK(or wait 10 seconds) to exit programming mode. Test all remotes to confirm successful programming.


------------------------------------------------------------------------------------------------------------------------


1998.5-2002 Mercury Cougar
1.Keep your foot off the brake pedal.
2.Insert the key in the ignition and turn it from OFF to RUN 4 times within 3 seconds. On the 4th turn leave the ignition on RUN.(off is where you can remove the key and run is the position just before the engine will start)
3.Turn the ignition to OFF. A red light will flash in the middle of the dash to confirm programming mode. (around the A/C control, some models in the inst cluster)
4.Within 20 seconds press and hold the lock button on the first keyless remote. Wait for dash light to flash(confirms programming) then release the lock button on remote. Wait 2 seconds but within 10 seconds repeat this process for all other remotes. If you only have one remote then continue to step 5.
5.Turn the ignition to ON to exit programming mode. Test all remotes to confirm successful programming.
If vehicle does not go into programming mode turn ignition from OFF to RUN 8 times instead of 4.


------------------------------------------------------------------------------------------------------------------------


1998-2003 Lincoln Town Car
2003-2004 Mercury Marauder
1.Keep your foot off the brake pedal.
2.Insert the key in the ignition and turn it from OFF to RUN 4 times within 3 seconds. On the 4th turn leave the ignition on RUN. When done correctly the door locks will cycle to signal entry into programming mode(off is where you can remove the key and run is the position just before the engine will start) If the door locks don't cycle the process is not being done correctly or the vehicle is not equipped with keyless entry.
3.Within 8 seconds press the lock button on all keyless remotes being programmed including any existing remotes. The doors locks will cycle to confirm successful programming of each remote.
4.Turn the ignition to OFF position to end programming mode. Test all remotes to confirm successful programming.

Use spaces to separate tags. Use single quotes (') for phrases.

Product Reviews

Write Your Own Review

Only registered users can write reviews. Please, log in or register